Cumulus Support

Hello

I have a rebadged Fine Offset 1080 - originally purchased in September 2010 - which has been recently replaced - November 2010 -by the retailer because the original consol appeared to develop a display fault whenever the Dew Point was lower than 0.0C. Immediately the Dew Point lowered to a minus figure the consol display showed -/76.1C or -/22.1F. The -/ character actually appear joined to form one character but I'm not clever enough to replicate this here! Curiously enough the replacement consol has today repeated the same error despite the fact that the whole system was replaced by the retailer. This was the first time since replacement that the Dew Point has reached minus C. levels.
Strangely enough the consol, despite displaying this erroneous figure, continues to send correct data i.e. Dew Points at minus levels to my computer which is then displayed by Cumulus. As I am still obtaining correct data via Cumulus for the minus Dew Points, I am relatively content but it would be good if the consol showed the same as Cumulus. It just seems as if the Dew Point display on the consol cannot cope with minus entries yet is able to send the correct figure to the computer. There are no problems with Dew Points above Freezing Point. All other consol readings are absolutely OK
It does seem odd that both the original system and its replacement are repeating the same 'error'. Has anyone else come across this problem with the Fine Offset 1080 and if so can it be resolved.

Tony

I wonder if it is telling you that it has changed to predicting Frost Point rather than Dew Point? Frost Point being measured from below 0C

I never look at the console so I have never seen it before -- must start looking

bumpy wrote:Strangely enough the consol, despite displaying this erroneous figure, continues to send correct data i.e. Dew Points at minus levels to my computer which is then displayed by Cumulus.

The station doesn't send dew point to the PC, Cumulus has to calculate it, so that's why you're seeing correct figures in Cumulus.

I seem to remember someone else having this problem with the console with negative dew point.

I didn't realise the console showed Dew Point - I very rarely look at a console.

Just had a look at mine only had it for a week from maplins
But it Does show
Temp, Wind-chill, Dew-point
Touch outside temp and use + or _ to scroll through the screens
and all are showing correctly on Easy-weather and Cumulus

Hi to all,

My first post, been here many times to the site in recent days and have purchased a PCE-FWS 20 Weatherstation from amazon which is really a Fine Offset 1080, (see link http://tinyurl.com/7ypmj8a)

All appeared to be working well until I started uploading to wunderground were I noticed a -3 dewpoint reading ???? I never even looked at dewpoint on my display , but when I did it showed up as -l75.4C

This appears to be the fault that bumpy had/has.

Anyone any ideas on this ?

Anyone came across this problem ?

Rang Amazon and they say to send everything back for a total refund and order another one.

I have ordered a new one and will return my original station when replacement arrives.
I might try new display with current setup first.

Thanks in advance for any help

Martin.

bumpy wrote:Hello

I have a rebadged Fine Offset 1080 - originally purchased in September 2010 - which has been recently replaced - November 2010 -by the retailer because the original consol appeared to develop a display fault whenever the Dew Point was lower than 0.0C. Immediately the Dew Point lowered to a minus figure the consol display showed -/76.1C or -/22.1F. The -/ character actually appear joined to form one character but I'm not clever enough to replicate this here! Curiously enough the replacement consol has today repeated the same error despite the fact that the whole system was replaced by the retailer. This was the first time since replacement that the Dew Point has reached minus C. levels.
Strangely enough the consol, despite displaying this erroneous figure, continues to send correct data i.e. Dew Points at minus levels to my computer which is then displayed by Cumulus. As I am still obtaining correct data via Cumulus for the minus Dew Points, I am relatively content but it would be good if the consol showed the same as Cumulus. It just seems as if the Dew Point display on the consol cannot cope with minus entries yet is able to send the correct figure to the computer. There are no problems with Dew Points above Freezing Point. All other consol readings are absolutely OK
It does seem odd that both the original system and its replacement are repeating the same 'error'. Has anyone else come across this problem with the Fine Offset 1080 and if so can it be resolved.

Tony