Page 7 of 7
Re: CustomLogs as module
Posted: Mon 20 May 2024 11:33 am
by philpugh
FWIW this is the result of the command ip a (host is RPi 5 Debian 12)
$ ip a
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
valid_lft forever preferred_lft forever
inet6 ::1/128 scope host noprefixroute
valid_lft forever preferred_lft forever
2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP group default qlen 1000
link/ether 2c:cf:67:00:82:9b brd ff:ff:ff:ff:ff:ff
inet 192.168.1.191/24 brd 192.168.1.255 scope global noprefixroute eth0
valid_lft forever preferred_lft forever
inet6 2a00
bd98:7801:5a21:956b:68b4:6bab/64 scope global dynamic noprefixroute
valid_lft 281sec preferred_lft 101sec
inet6 fe80::bdf4:da8c:188:def3/64 scope link noprefixroute
valid_lft forever preferred_lft forever
3: wlan0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group default qlen 1000
link/ether 2c:cf:67:00:82:9c brd ff:ff:ff:ff:ff:ff
Re: CustomLogs as module
Posted: Tue 21 May 2024 12:50 pm
by HansR
Hi Phil,
7003 was not released as an official release yet, I tried something for solving the issue by @Dador.
But a next release will be without optimisation and apparently I have to set something straight.
Thanks for the observation!
Re: CustomLogs as module
Posted: Tue 21 May 2024 5:46 pm
by HansR
@Dador, @PhilPugh:
Please find attached v7003 for testing. If OK, this will be the release so all your problems should be gone.
Re: CustomLogs as module
Posted: Tue 21 May 2024 7:40 pm
by Dador
I report that it works well.
Charts are drawn without any problems.
Re: CustomLogs as module
Posted: Thu 23 May 2024 2:45 pm
by philpugh
HansR: Sorry about that but 7.0.3 working fine now!
Phil
Re: CustomLogs as module
Posted: Tue 06 Aug 2024 10:34 am
by Dador
Would it be possible in the future for the CustomLog module to be able to create charts for other CMX instances as well?
I'm asking because I currently have 3 working CMXs (1x Ecowitt, 2x Davis) and seeing e.g. rainfall from 3 rain gauges on one graph
that would be something!
Re: CustomLogs as module
Posted: Tue 06 Aug 2024 4:57 pm
by HansR
From far away both physically and spiritually
I would say that is not possible as each CMX instance would have its own CUtils using its data.
However you might think about importing the data to some user defined webtag or use an external sensor system to import the data. Whatever you do, you need to get all three raingauge data in one CMX instance database to be able to create a chart displaying them all. I dont see a possibility to have three CMX being served by one CUtils.
See you (much) later...
bd98:7801:5a21:956b:68b4:6bab/64 scope global dynamic noprefixroute 