Compatible Airlink setup

[laulau]

Hi,
I have a Davis Airlink compatible device :https://www.meteocercal.info/forum/thread-1970.html

/ 20230423170033
// http://192.168.1.215/v1/current_conditions

{
"data": {
"did": "001D0A100021",
"name": "AQM-III-P",
"ts": 1682262033,
"conditions": [
{
"lsid": 0,
"data_structure_type": 6,
"temp": 69.56288,
"hum": 54.78339,
"dew_point": 52.57102,
"wet_bulb": 59.17295,
"heat_index": 69.56288,
"pm_1_last": 29.40294,
"pm_2p5_last": 46.47561,
"pm_10_last": 55.96043,
"pm_1": 29.40294,
"pm_2p5": 46.47561,
"pm_2p5_last_1_hour": 53.42764,
"pm_2p5_last_3_hours": 76.9452,
"pm_2p5_last_24_hours": 10.20296,
"pm_2p5_nowcast": 59.4,
"pm_10": 55.96043,
"pm_10_last_1_hour": 64.42789,
"pm_10_last_3_hours": 85.62026,
"pm_10_last_24_hours": 11.21694,
"pm_10_nowcast": 66.8,
"last_report_time": 1682262033,
"pct_pm_data_last_1_hour": 100,
"pct_pm_data_last_3_hours": 100,
"pct_pm_data_nowcast": 100,
"pct_pm_data_last_24_hours": 100
}
]
},
"error": 0
}

I'm trying to set it up in CMX.
Are the weathelink API key and secret needed to achieve that ?
thanks.

[mcrossley]

No API details required for the live data, but you will not have catch-up or health data.

[HansR]

I have the same device, just fill in the IP and the (AirLink host)name and you're set. CMX will start asking the data and when found it stores it.

[laulau]

Not working for me !

Capture.JPG

The anotation is confusing me !

[HansR]

You only fill in the IP and the hostname.
Station ID remains 0 or leave it empty (you use -1, that may be the cause).

The upper section with your yellow notes remains empty.

The AQM-III does behave differently than an official AirLink in that it does not registrate or communicate with Davis, it just responds to the query by CMX.

[HansR]

And apparently even the hostname is not required (according to the AQM-III instructions)

[laulau]

Seems that a restart was needed to have the Airlink data.
But have this message :

Capture.JPG

[HansR]

OK. Looks good.
You have two AQM-III?

[laulau]

Yes,
One is a original AQM III, the second one is a AQM II updated to AQM III withe an addon prototype board.

Proto.jpg

[laulau]

Hi,
In Extra sensors -> AirLink sensors i have the indoor and outdoor readings.
How can i see those values in the charts?
Thanks

[HansR]

Hi,
In Extra sensors -> AirLink sensors i have the indoor and outdoor readings.
How can i see those values in the charts?
Thanks

OK. I assume you are talking about CUtils and not about the standard CMX website (old and new style).
Is that correct? If so, could you please ask the question in the CUtils forum?

[laulau]

No I thought as I have the data in CMX I could see it in the CMX charts of user interface.

Capture.JPG

[mcrossley]

The AirLink data appears under the "Air Quality" graph selection. The CO2 sensor is an Ecowitt device.