Page 1 of 2
Problems to configure CumulusMX
Posted: Sun 28 Feb 2021 2:47 pm
by paologambal
I installed the program as per your site and I connected the Oregon WMR928nx station on the rs-232 port but unfortunately it does not connect. When I go to run sudo mono on the terminal it gives me the following errors that I send them. If you can help me, thank you. Regards.
Re: Problems to configure CumulusMX
Posted: Sun 28 Feb 2021 2:51 pm
by ConligWX
if you care to look at the screen shots you have posted it says Specified port number not open.
find out what com port your serial is plugged into and assign that in the Cumulus.ini
Re: Problems to configure CumulusMX
Posted: Sun 28 Feb 2021 2:57 pm
by HansR
You are running build 3042, that is very old. I would advise to upgrade.
And while you are at it, please check the versions status of Mono and Linux as well.
The most likely cause is rooted in version incompatibility.
Re: Problems to configure CumulusMX
Posted: Sun 28 Feb 2021 3:40 pm
by water01
HansR wrote: ↑Sun 28 Feb 2021 2:57 pm
You are running build 3042, that is very old. I would advise to upgrade.
And while you are at it, please check the versions status of Mono and Linux as well.
The most likely cause is rooted in version incompatibility.
How on earth does someone get hold of build 3042, that is while Steve was still doing the builds!!
Re: Problems to configure CumulusMX
Posted: Sun 28 Feb 2021 4:18 pm
by freddie
water01 wrote: ↑Sun 28 Feb 2021 3:40 pmHow on earth does someone get hold of build 3042, that is while Steve was still doing the builds!!
It's 3043 but it's still ancient and should be trying a newer version
Re: Problems to configure CumulusMX
Posted: Sun 28 Feb 2021 4:24 pm
by PaulMy
How on earth does someone get hold of build 3042,
You want it
Enjoy,
Paul
Re: Problems to configure CumulusMX
Posted: Sun 28 Feb 2021 4:35 pm
by HansR
water01 wrote: ↑Sun 28 Feb 2021 3:40 pm
How on earth does someone get hold of build 3042, that is while Steve was still doing the builds!!
Collectors item!
Re: Problemi di configurazione di CumulusMX
Posted: Mon 15 Mar 2021 8:07 pm
by paologambal
On the raspberry Pi 2 reinstalled Raspbian buster vers. 2020.8.20 Desktop and CumulusMx 3.8.3 distr.3093 but I am still having problems updating CumulusMX from the Oregon Wmr928 station (serial port rs232 to usb port of the raspberry). of the screenshot of the station errors. Thank you if someone can help me.
Re: Problems to configure CumulusMX
Posted: Mon 15 Mar 2021 8:16 pm
by ConligWX
if you care to look at the first screenshot.
it says near the bottom:
Code: Select all
An error has occurred - please zip up the MXdiags folder and post it in the forum.
Where is your zip file?
can you post the output of this command:
Re: Problems to configure CumulusMX
Posted: Thu 18 Mar 2021 8:11 pm
by paologambal
sending zip file
Re: Problems to configure CumulusMX
Posted: Thu 18 Mar 2021 8:18 pm
by paologambal
Tonight I tried to install CumulusMX version 3.0.0.0 build 3044 but to my surprise I am again with problems that I post with screenshots.
Thanks for your help.
Re: Problems to configure CumulusMX
Posted: Thu 18 Mar 2021 8:45 pm
by freddie
Something else on your Pi listening on port 8998?
Re: Problems to configure CumulusMX
Posted: Thu 18 Mar 2021 8:49 pm
by mcrossley
We go right back to the first response above which you have not really answered.
What are you entering in Cumulus MX as the serial port name?
Re: Problemi di configurazione di CumulusMX
Posted: Fri 19 Mar 2021 1:16 pm
by paologambal
What do you mean by serial port name? tcp port? on the configuration of the oregon? The number 22222 is entered.
Re: Problems to configure CumulusMX
Posted: Fri 19 Mar 2021 1:36 pm
by ConligWX
I think he means the name of the comport entry in cumulus.ini
like so:
Code: Select all
ComportName=/dev/ttyUSB0
or
ComportName=COM1