Cumulus Support

Has anyone managed to receive the signal directly from the weather station (Maplin N96GY) onto a Raspberry PI so as to by pass the receiver/display? I have looked on a few internet forums but cannot see a route to do this without mounting the Raspberry PI outside with the weather station, then using WIFI to upload the data directly.

Have you seen this?. I've not read it thru fully, but wondered if it'd be of help. I'm hoping to do something similar as my console is kaput!

http://www.susa.net/wordpress/2012/08/r ... nd-rfm12b/

Hi,

Ah yes, I thought I'd answered that question.

One of the hazards of an OP asking the same question in more than one thread.

Cheers, Alan.

I am aware this is an old post but in the light of newer hardware and software.....

I'm currently using a USB radio dongle to capture the radio signals from a Maplins N96GY using rtl433 on a raspberry pi.

USB radio device is an RTL-SDR RTL2832U DVB-T Tuner Dongles

This is a lockdown/retirement project to keep me relatively sane.

* Searched for RTL433 and loaded it into Pi
* Searched for HiveMQ broker for RTL433 to publish data to
* Wrote python script to subscribe to the broker and read the RTL433 published data
(obviously this could done without the broker but I am familiar with broker pub/sub)
* Python script creates Easyweather.dat file for CumulusMX to read.
* Currently waiting for a pressure sensor to hook into it.
This will need another python script to read the pressure and then publish it to the same broker for it to be picked up by the first python script.

Current Progress:
The display on the left is from one Raspberry pi box which is USB connected to the Maplins supplied Weather Console.
The display on the right is from another pi box which is connected the the RTL dongle. The pressure numbers on this display come from the left hand CumulusMX which
is sending the pressure data to the hiveMQ broker as a temporary measure until I get the Waveshare BMP388 pressure and temperature chip to attach to the pi.
Because of timing differences between the two setups in reading the console and the broker there is usually a delay and delta between the displays. This usually
only last for 30 seconds.
.

Looks like that will keep you busy.

Pleased to say I have it working now on a Pi 4 using python scripts.

Radio signals from Maplins Fine Offset transmitter picked up by RTL dongle and published to HiveMQ MQTT broker.
Indoor temperature and pressure sensor readings retrieved from BMP388 and also published to MQTT broker.

MQTT broker subscribed to by another python script which creates the Easyweather.dat file and places it in the CumulusMX directory.
CumulusMX configured to read Easyweather.dat file and display as normal.

Interestingly the calibration settings for the pressure is +14 in the unit reading the console and 13 in the unit read the BMP sensor and
they do track within a few tenths of millibars (so far!)

The biggest challenge unsurprisingly was sorting the software out for the BMP388.
Not many software examples around and I had to debug one of the examples to make it work .

Pressure Sensor:
https://www.amazon.co.uk/WENDi-BMP388-B ... B07QW1449Z

HiveMQ Broker:
https://bit.ly/3sbTxVJ

Leaving them running side by side for a while to see how the pressures track each other.

Update:

Just updated my setup to use Ecowitt HTTP protocol rather than Easweather.dat file to allow me to add a few more sensors.

Lightning detector on its way!

Hi,

I came across this post while looking at ways to integrate my various sensors to cumulus mx.
I am using mosquito mqtt broker to push data from RASPIs that I get sensor data from i2c(etc).

So I wanted to see how I can use cumulus mx to subscribe to mqtt topic/s and import data from there.

Any new developments in this area? I see that there is only mqtt to send data but not to receive and this post is promising, but 2,5 years old

Don't think you can do it directly. But you could write a utility that subscribes to mqtt topics and reformulates the data in a way that can be pushed (or pulled) to (by) MX. I think somebody did similar earlier in this topic.

Thank you for your answer, I was hoping that (@watsonm) Mike would jump in to give his status on the topic instead of re-inventing the wheel.

but yes if "no joy" then I guess could write a small python script to do the job and maybe contribute it.

Hi, sorry haven't been around for a while . I'll blame old age (75) and associated heart problems. In fact only came out of hospital yesterday 19/5/2024. i'll have a go at replying in a day or two as I spend most of my time asleep at the moment. Maybe getting the brain working on answering the query will be the stimulus for kick starting me!!