Cumulus Support

Hi,

I have just set up a weather station using a Davis VP2 with Weatherlink IP unit I am also using Cumulus software. When using the Davis software after entering my Latitude and Longitude and logging on to findU it give my correct location, however, when using Cumulus no matter what I set my Latitude and Longitude to it is nowhere near my location! So can anyone help me with this problem?

I look forward to your replies.

HKB

This is uploading to CWOP, yes? You probably haven't entered your co-ordinates into Cumulus in the correct format. Can you show what you've put into Weatherlink and Cumulus, and give your CWOP ID, please?

steve wrote:This is uploading to CWOP, yes? You probably haven't entered your co-ordinates into Cumulus in the correct format. Can you show what you've put into Weatherlink and Cumulus, and give your CWOP ID, please?

Hi Steve,

CWOP ID EW3727.

Correct uploading to CWOP and viewed via the following link: http://www.findu.com/cgi-bin/wx.cgi?call=EW3727

This is the GPS information from my GPS software on my phone:

Lat N 53°04'21.873

Lon W 002°31'16.536

This is what I have in the Davis software:

Latitude: 53 4 21 N

Longitude: 2 31 17 E

I also "had" the above in Cumulus but it put me in the middle of the ocean!

So I now have the following:

Latitude: 53 4 21 N

Longitude: 0 0 2 E

That gets me on dry land at the following location: "EW3727 --- 6.2 miles northwest of BOSTON, UNITED KINGDOM"

Running on the Davis WeatherLink software v 6.0.3 it shows correctly at: "EW3727 --- 3.1 miles southwest of CREWE, UNITED KINGDOM"

I also have another problem which started a couple of days ago, now when I run Cumulus "New Record" no longer flashes but it is updating ok, however if I run Comulus first on my laptop then start it on my destop, I first get "error 32701" on the desktop and after shutting it down on the laptop Cumulus starts working fine!

Thanks for your time Steve.

Regards

Bob.

Hong Kong Bob wrote:This is the GPS information from my GPS software on my phone:

Lat N 53°04'21.873

Lon W 002°31'16.536

This is what I have in the Davis software:

Latitude: 53 4 21 N

Longitude: 2 31 17 E

I also "had" the above in Cumulus but it put me in the middle of the ocean!

So I now have the following:

Latitude: 53 4 21 N

Longitude: 0 0 2 E

Your GPS says you're west of the meridian but you're putting east into Cumulus. If the bit after the minutes symbol from your GPS is seconds, then

Lat N 53°04'21.873

Lon W 002°31'16.536

should be put into Cumulus as

53 4 22 N
2 31 17 W

I also have another problem which started a couple of days ago, now when I run Cumulus "New Record" no longer flashes but it is updating ok

See the FAQ: http://wiki.sandaysoft.com/a/FAQ#My_.E2 ... d_flashing

however if I run Comulus first on my laptop then start it on my destop, I first get "error 32701" on the desktop and after shutting it down on the laptop Cumulus starts working fine!

Yes, you can't connect from two different PCs at the same time.

Well Steve that was easy well it was when you know what you are doing It's all reading correct now so thanks for that, I did know you could not run Cumulus on two PC's at the same time, well I did after trying. I have read the FAQ re the "New record" so that also sorts that out. One thing if I do start Cumulus up as I said before the "new Record " keeps flashing all the time

Keep up the good work.

Best regards,

Bob.

steve wrote:

Hong Kong Bob wrote:This is the GPS information from my GPS software on my phone:

Lat N 53°04'21.873

Lon W 002°31'16.536

This is what I have in the Davis software:

Latitude: 53 4 21 N

Longitude: 2 31 17 E

I also "had" the above in Cumulus but it put me in the middle of the ocean!

So I now have the following:

Latitude: 53 4 21 N

Longitude: 0 0 2 E

Your GPS says you're west of the meridian but you're putting east into Cumulus. If the bit after the minutes symbol from your GPS is seconds, then

Lat N 53°04'21.873

Lon W 002°31'16.536

should be put into Cumulus as

53 4 22 N
2 31 17 W

I also have another problem which started a couple of days ago, now when I run Cumulus "New Record" no longer flashes but it is updating ok

See the FAQ: http://wiki.sandaysoft.com/a/FAQ#My_.E2 ... d_flashing

however if I run Comulus first on my laptop then start it on my destop, I first get "error 32701" on the desktop and after shutting it down on the laptop Cumulus starts working fine!

Yes, you can't connect from two different PCs at the same time.

You might be able to connect with two PC's by using Virtual VP. I do it all of the time. I don't know if the new Davis firmware effects the IP version the same as it does the USB/serial versions which seems to not work with VVP.

http://www.softwx.com/weather/virtualvp.html

Jim Brown wrote:You might be able to connect with two PC's by using Virtual VP. I do it all of the time. I don't know if the new Davis firmware effects the IP version the same as it does the USB/serial versions which seems to not work with VVP.

http://www.softwx.com/weather/virtualvp.html

Hi Jim,

Thanks for your reply and information. I have had a look a the website, I downloaded VPLive to give it a try, it is a nice piece of software.

Regards,

Bob.