Welcome to the Cumulus Support forum.
Latest Cumulus MX V3 release 3.28.6 (build 3283) - 21 March 2024
Cumulus MX V4 beta test release 4.0.0 (build 4019) - 03 April 2024
Legacy Cumulus 1 release 1.9.4 (build 1099) - 28 November 2014
(a patch is available for 1.9.4 build 1099 that extends the date range of drop-down menus to 2030)
Download the Software (Cumulus MX / Cumulus 1 and other related items) from the Wiki
Latest Cumulus MX V3 release 3.28.6 (build 3283) - 21 March 2024
Cumulus MX V4 beta test release 4.0.0 (build 4019) - 03 April 2024
Legacy Cumulus 1 release 1.9.4 (build 1099) - 28 November 2014
(a patch is available for 1.9.4 build 1099 that extends the date range of drop-down menus to 2030)
Download the Software (Cumulus MX / Cumulus 1 and other related items) from the Wiki
MX data/chart resolution
Moderator: mcrossley
-
- Posts: 32
- Joined: Wed 02 Sep 2020 6:52 am
- Weather Station: WA1081
- Operating System: Win 7
- Location: Melbourne, Australia
- Contact:
MX data/chart resolution
Since upgrading to MX I have been fairly happy, however...
I observed on my graphs that rain minimum increments are mostly displayed as 0.4mm yet my bucket-tipper corresponds to 0.3mm
On old Cumulus the rain graph increments/steps were always 0.3mm so that I would see 0.3, 0.6, 0.9, 1.2 etc. With MX I can usually see 0.4, 0.8, 1.2, 1.6 but every now and then a 0.3 increment occurs.
I figured this was a graphing resolution matter until I noticed these odd values also on the main page i.e. 'Now'.
Further to the above I also noticed on the external temperature graph where it resolves to 0.1 degrees that sometimes it steps as much as 0.4 in 60 seconds and that is during steady weather conditions i.e. not the sun in/out behind clouds.
As I am typing this I realise I have not examined the data files and shall do so later in the day - but I'll post anyway in case others have had similar issues.
I observed on my graphs that rain minimum increments are mostly displayed as 0.4mm yet my bucket-tipper corresponds to 0.3mm
On old Cumulus the rain graph increments/steps were always 0.3mm so that I would see 0.3, 0.6, 0.9, 1.2 etc. With MX I can usually see 0.4, 0.8, 1.2, 1.6 but every now and then a 0.3 increment occurs.
I figured this was a graphing resolution matter until I noticed these odd values also on the main page i.e. 'Now'.
Further to the above I also noticed on the external temperature graph where it resolves to 0.1 degrees that sometimes it steps as much as 0.4 in 60 seconds and that is during steady weather conditions i.e. not the sun in/out behind clouds.
As I am typing this I realise I have not examined the data files and shall do so later in the day - but I'll post anyway in case others have had similar issues.
- mcrossley
- Posts: 12765
- Joined: Thu 07 Jan 2010 9:44 pm
- Weather Station: Davis VP2/WLL
- Operating System: Bullseye Lite rPi
- Location: Wilmslow, Cheshire, UK
- Contact:
Re: MX data/chart resolution
Interesting - the graph data also has 0.4 as the first increment, so it is coming from Cumulus.
You don't have a rain multiplier set in the configuration do you?
You don't have a rain multiplier set in the configuration do you?
-
- Posts: 32
- Joined: Wed 02 Sep 2020 6:52 am
- Weather Station: WA1081
- Operating System: Win 7
- Location: Melbourne, Australia
- Contact:
Re: MX data/chart resolution
Thanks Mark,
When I posted I was convinced that this issue arose with MX as I can’t recall seeing it with older Cumulus graphs and I usually study rain graphs carefully.
Data files however have proven me wrong. Looking at July 20 data (pre MX) I did see rain increments of 0.4 (rather than 0.3) occurring at times with the odd 0.3 thrown in. I assume the odd 0.3 is there as a cumulative correction?
Yes, I have always used a rain multiplier but it has never been a factor.... until it seems when I re-calibrated around April taking it up to x 1.2 so that must have been the Camel’s straw.
So the multiplier is the answer thanks Mark
Whilst I have you attention, is there an easy way I can have a lost sensor alarm displayed on my uploaded webpage?
When I posted I was convinced that this issue arose with MX as I can’t recall seeing it with older Cumulus graphs and I usually study rain graphs carefully.
Data files however have proven me wrong. Looking at July 20 data (pre MX) I did see rain increments of 0.4 (rather than 0.3) occurring at times with the odd 0.3 thrown in. I assume the odd 0.3 is there as a cumulative correction?
Yes, I have always used a rain multiplier but it has never been a factor.... until it seems when I re-calibrated around April taking it up to x 1.2 so that must have been the Camel’s straw.
So the multiplier is the answer thanks Mark
Whilst I have you attention, is there an easy way I can have a lost sensor alarm displayed on my uploaded webpage?
- mcrossley
- Posts: 12765
- Joined: Thu 07 Jan 2010 9:44 pm
- Weather Station: Davis VP2/WLL
- Operating System: Bullseye Lite rPi
- Location: Wilmslow, Cheshire, UK
- Contact:
Re: MX data/chart resolution
You need to use the web tag for the alarm - <#SensorContactLost> and embed that in either in the name of an image file (it has a value 1 or 0), or use it in some JScript to set some text. If you search the forum for examples of using the record set web tag you should find something suitable.
-
- Posts: 32
- Joined: Wed 02 Sep 2020 6:52 am
- Weather Station: WA1081
- Operating System: Win 7
- Location: Melbourne, Australia
- Contact:
Re: MX data/chart resolution
Mark,
I mentioned the above in my first post and now I have a good example, attached.
Note the larger steps around time 05:30 and again around 07:30. They are 0.3 degrees and on most parts of the graph the smallest resolution of 0.1 degrees appears often.
Also the 0.3 steps are abrupt occurring over only 1 minute whereas my graph data is only uploaded every 5 minutes.
You do not have the required permissions to view the files attached to this post.
- mcrossley
- Posts: 12765
- Joined: Thu 07 Jan 2010 9:44 pm
- Weather Station: Davis VP2/WLL
- Operating System: Bullseye Lite rPi
- Location: Wilmslow, Cheshire, UK
- Contact:
Re: MX data/chart resolution
Well 0.3 degree change in a minute isn't unheard of, but normally you would see it as part a larger rapid rise or fall in temperature.
I'd say the base station is missing some transmissions from your remote sensor. Iirc it takes some time before the sensor lost flag gets set, so it could be missing some messages, then picking up again and the temp has changed a bit.
I'm not sure what you mean, the graphs plot a data point every minute.Also the 0.3 steps are abrupt occurring over only 1 minute whereas my graph data is only uploaded every 5 minutes.
I'd say the base station is missing some transmissions from your remote sensor. Iirc it takes some time before the sensor lost flag gets set, so it could be missing some messages, then picking up again and the temp has changed a bit.
-
- Posts: 26
- Joined: Sat 14 Nov 2009 12:34 pm
- Weather Station: Vantage pro+
- Operating System: RPi3 Model 3 running Buster
- Location: Clifton, Beds
- Contact:
Re: MX data/chart resolution
I was just thinking that it looks like missing data from the sensors due to the long flat period before each jump
-
- Posts: 86
- Joined: Sat 02 Jan 2016 10:10 pm
- Weather Station: Davis VP2+, WLL & Airlink
- Operating System: Win 10 64bit / RPi Buster
- Location: Nantwich, UK
- Contact:
Re: MX data/chart resolution
Perhaps a failing sensor? My console pressure sensor started exhibiting that kind of symptom, and that was the trigger for replacement of the component.
Regards Jon
https://duncreggan.net/cumulusmx/index.htm
https://duncreggan.net/cumulusmx/index.htm
-
- Posts: 32
- Joined: Wed 02 Sep 2020 6:52 am
- Weather Station: WA1081
- Operating System: Win 7
- Location: Melbourne, Australia
- Contact:
Re: MX data/chart resolution
Thank you all and upon carefully examining wind speed and external humidity graphs at the same time interval as temp they seem to confirm a loss of signal from the remote unit.
If I ever suspected a loss of signal I could check that on the old Cumulus with a permanently set fail light.
If I ever suspected a loss of signal I could check that on the old Cumulus with a permanently set fail light.
- mcrossley
- Posts: 12765
- Joined: Thu 07 Jan 2010 9:44 pm
- Weather Station: Davis VP2/WLL
- Operating System: Bullseye Lite rPi
- Location: Wilmslow, Cheshire, UK
- Contact:
Re: MX data/chart resolution
I know its not the same, but you can enable the Data Stopped and Sensor Contact lost alarms, and leave the Dashboard running. It will alarm when the signal is lost.
The log file should contain a record of the events too.
The log file should contain a record of the events too.
-
- Posts: 32
- Joined: Wed 02 Sep 2020 6:52 am
- Weather Station: WA1081
- Operating System: Win 7
- Location: Melbourne, Australia
- Contact:
Re: MX data/chart resolution
Mark,
I enabled those alarms a few days ago but they are not flags, they are dynamic and off/on/off.
I tested with a temperature alarm and unless I stay glued to the screen I don't know if it ever briefly goes red.
Is there some logging where alarm activity is recorded?
I enabled those alarms a few days ago but they are not flags, they are dynamic and off/on/off.
I tested with a temperature alarm and unless I stay glued to the screen I don't know if it ever briefly goes red.
Is there some logging where alarm activity is recorded?
- mcrossley
- Posts: 12765
- Joined: Thu 07 Jan 2010 9:44 pm
- Weather Station: Davis VP2/WLL
- Operating System: Bullseye Lite rPi
- Location: Wilmslow, Cheshire, UK
- Contact:
Re: MX data/chart resolution
The alarms are not logged - except for Data Stopped, which appears in the MXdiags log file.
The alarms may be be getting a bit of love in the next release
The alarms may be be getting a bit of love in the next release