10.8 mph was my highest gust that day!
Welcome to the Cumulus Support forum.
Latest Cumulus MX V3 release 3.28.6 (build 3283) - 21 March 2024
Cumulus MX V4 beta test release 4.0.0 (build 4019) - 03 April 2024
Legacy Cumulus 1 release 1.9.4 (build 1099) - 28 November 2014
(a patch is available for 1.9.4 build 1099 that extends the date range of drop-down menus to 2030)
Download the Software (Cumulus MX / Cumulus 1 and other related items) from the Wiki
Latest Cumulus MX V3 release 3.28.6 (build 3283) - 21 March 2024
Cumulus MX V4 beta test release 4.0.0 (build 4019) - 03 April 2024
Legacy Cumulus 1 release 1.9.4 (build 1099) - 28 November 2014
(a patch is available for 1.9.4 build 1099 that extends the date range of drop-down menus to 2030)
Download the Software (Cumulus MX / Cumulus 1 and other related items) from the Wiki
Davis anemometer transmitter problems
-
- Posts: 317
- Joined: Sat 05 Feb 2011 7:13 pm
- Weather Station: VP2
- Operating System: Windows - all flavours
- Location: Littleport, East Cambs, UK
Re: Davis anemometer transmitter problems
No, it's not a common or specific symptom of supercap or board failure, but simply falls into the more general (and unhelpful) category of odd readings. It's impossible to say for sure but this one does sound to me a little more like a failure of some other board component (or eg a dry joint or microcrack in one of the traces on the board) than the supercap itself, especially since the supercap leads look clean. In theory you could try a very careful inspection of the board in bright light with a magnifying glass but it's rarely a productive exercise I'm afraid.
One other thing you could try is to disconnect the T/H sensor. Occasionally when this sensor starts to fail it can cause odd symptoms elsewhere - most commonly failure of packet transmission, but sometimes other effects too.
Sorry, not very helpful I know.
-
- Posts: 83
- Joined: Mon 30 Jun 2014 12:02 pm
- Weather Station: Instromet Mk 3
- Operating System: Raspberry Pi Zero & CumulusMX
- Location: Kent
Re: Davis anemometer transmitter problems
Freddie I think you said that the transmitter in use was solely for Windspeed/direction.
With what has been said so far it could be a supercapacitor on its way out. With a few more electronic bits and pieces the solar panel, battery and supecap will all be in a parallel configuration. The electronics will stop back feeding etc. If the circuit board is the problem then you have no real choice but to buy a spare unit. Soldering surface mount components is not for the faint hearted!
If the supercap is the problem, which it could be, then I would try a 'simple test' to prove it.
Using a pair of very fine nose wire cutters I would cut one of the capacitor leads midway between the board and the capacitor. This could allow you to re-solder it later if the capacitor is ok. Take care not to bend the leads to the capacitor they dont like it!
With one lead disconnected on the capacitor see if a battery/solar panel gives any duration at all.
If not then it could be the solar panel (very unlikely) but that could be tested by disconnecting the cct board to solar panel plug and running purely on battery.
Modern electronics are very sensitive to power supply stability, if your supercap is going faulty and put varying loads on the battery/solar panel, these fluctuations could give eroneous readings.
Anyway good luck
Dave
With what has been said so far it could be a supercapacitor on its way out. With a few more electronic bits and pieces the solar panel, battery and supecap will all be in a parallel configuration. The electronics will stop back feeding etc. If the circuit board is the problem then you have no real choice but to buy a spare unit. Soldering surface mount components is not for the faint hearted!
If the supercap is the problem, which it could be, then I would try a 'simple test' to prove it.
Using a pair of very fine nose wire cutters I would cut one of the capacitor leads midway between the board and the capacitor. This could allow you to re-solder it later if the capacitor is ok. Take care not to bend the leads to the capacitor they dont like it!
With one lead disconnected on the capacitor see if a battery/solar panel gives any duration at all.
If not then it could be the solar panel (very unlikely) but that could be tested by disconnecting the cct board to solar panel plug and running purely on battery.
Modern electronics are very sensitive to power supply stability, if your supercap is going faulty and put varying loads on the battery/solar panel, these fluctuations could give eroneous readings.
Anyway good luck
Dave
-
- Posts: 2473
- Joined: Wed 08 Jun 2011 11:19 am
- Weather Station: Davis Vantage Pro 2 + Ecowitt
- Operating System: GNU/Linux Ubuntu 22.04 LXC
- Location: Alcaston, Shropshire, UK
- Contact:
Re: Davis anemometer transmitter problems
Thanks for all the responses on this thread - most helpful.
My setup started behaving itself again around the time of my last message, and is continuing to do so now at 10 days on. So I'm going to cross my fingers for the moment
My setup started behaving itself again around the time of my last message, and is continuing to do so now at 10 days on. So I'm going to cross my fingers for the moment
-
- Posts: 3390
- Joined: Wed 06 May 2009 6:29 pm
- Weather Station: Davis VP2 with Daytime FARS
- Operating System: Windows XP SP3
- Location: Cheadle Hulme, Cheshire, England
- Contact:
Re: Davis anemometer transmitter problems
Glad to hear that Freddie. I dread anemometer problems but especially now as my trusty mate who goes onto my roof wouldn’t be available. Fingers crossed it remains stable.
- mcrossley
- Posts: 12756
- Joined: Thu 07 Jan 2010 9:44 pm
- Weather Station: Davis VP2/WLL
- Operating System: Bullseye Lite rPi
- Location: Wilmslow, Cheshire, UK
- Contact:
Re: Davis anemometer transmitter problems
I've changed my roof setup so that it is all on a single 2" pole. Transmitter clamped to the bottom, anemo & solar to top. The cables run down the inside of the pole. I now have two sliding clamps on the P-K brackets. Which means I now just have to get up as far as the brackets, release those and the pole slides down. When I'm done, slide it back up again, clamp it off and it retains its vertical alignment.
-
- Posts: 3390
- Joined: Wed 06 May 2009 6:29 pm
- Weather Station: Davis VP2 with Daytime FARS
- Operating System: Windows XP SP3
- Location: Cheadle Hulme, Cheshire, England
- Contact:
Re: Davis anemometer transmitter problems
Mark, if I recall your house has a gable end making your arrangement easier. I have a three-sided roof and access is easiest from the flat garage roof on one side. The solar panels have to be negotiated but if my mate sticks to the ridge tile area that's not a problem.
I did think about having something similar to yours with two large clamps on the side of the house but the length of the pole would make it very cumbersome. The existing pole is around 2" or less and the bracket it's attached to is solid having been there for over 40 years!
I used to get up there 30 years ago and admire the view when adjusting the TV aerial. How times change!
I did think about having something similar to yours with two large clamps on the side of the house but the length of the pole would make it very cumbersome. The existing pole is around 2" or less and the bracket it's attached to is solid having been there for over 40 years!
I used to get up there 30 years ago and admire the view when adjusting the TV aerial. How times change!
-
- Posts: 2473
- Joined: Wed 08 Jun 2011 11:19 am
- Weather Station: Davis Vantage Pro 2 + Ecowitt
- Operating System: GNU/Linux Ubuntu 22.04 LXC
- Location: Alcaston, Shropshire, UK
- Contact:
Re: Davis anemometer transmitter problems
I'm waking this topic up again as I have a refinement to the description of the problem.
After my earlier problems I took down my anemo and packed it away ready for an upcoming house move.
It is now installed in the new location, and I noticed that the direction is being sent to the console and it is varying with the position of the vane. The speed is still registering as zero (the cups are spinning around).
Any pointers as to what could be wrong>
After my earlier problems I took down my anemo and packed it away ready for an upcoming house move.
It is now installed in the new location, and I noticed that the direction is being sent to the console and it is varying with the position of the vane. The speed is still registering as zero (the cups are spinning around).
Any pointers as to what could be wrong>
- mcrossley
- Posts: 12756
- Joined: Thu 07 Jan 2010 9:44 pm
- Weather Station: Davis VP2/WLL
- Operating System: Bullseye Lite rPi
- Location: Wilmslow, Cheshire, UK
- Contact:
Re: Davis anemometer transmitter problems
Is it old model with a reed switch, or the newer one with a hall effect module? (Generally if it has a brass pointer it is the new model - don't know if that is always true?)
Could only be a few things really...
Bust reed switch/hall effect module - the reed switch is far more likely to fail.
A break in the cable.
Dodgy plug on the end of the cable.
Bent pin in the ISS socket.
Corroded contacts on the plug/socket - they should be gold plated, but can still fail. Davis normally pack a reasonable amount of silicone grease in the socket to protect against this. The grease could also get contaminated with debris and prevent a good contact.
Faulty ISS.
I'm pecking on my phone, so more detail will have to wait...
Could only be a few things really...
Bust reed switch/hall effect module - the reed switch is far more likely to fail.
A break in the cable.
Dodgy plug on the end of the cable.
Bent pin in the ISS socket.
Corroded contacts on the plug/socket - they should be gold plated, but can still fail. Davis normally pack a reasonable amount of silicone grease in the socket to protect against this. The grease could also get contaminated with debris and prevent a good contact.
Faulty ISS.
I'm pecking on my phone, so more detail will have to wait...
-
- Posts: 317
- Joined: Sat 05 Feb 2011 7:13 pm
- Weather Station: VP2
- Operating System: Windows - all flavours
- Location: Littleport, East Cambs, UK
Re: Davis anemometer transmitter problems
Think Mark has covered all of the obvious points, but for the record here's the relevant topic on our knowledgebase:
https://www.manula.com/manuals/pws/davi ... ind-issues
https://www.manula.com/manuals/pws/davi ... ind-issues
-
- Posts: 2473
- Joined: Wed 08 Jun 2011 11:19 am
- Weather Station: Davis Vantage Pro 2 + Ecowitt
- Operating System: GNU/Linux Ubuntu 22.04 LXC
- Location: Alcaston, Shropshire, UK
- Contact:
Re: Davis anemometer transmitter problems
Thanks Mark and John. I will start off with the cheapest option (cleaning the plug/socket) once I get a bit of spare time
I will let you know how it goes
I will let you know how it goes
- ConligWX
- Posts: 1613
- Joined: Mon 19 May 2014 10:45 pm
- Weather Station: Davis vPro2+ w/DFARS + AirLink
- Operating System: Ubuntu 22.04 LTS
- Location: Bangor, NI
- Contact:
Re: Davis anemometer transmitter problems
Hi Freddie,
Just curious as to what all that is around each socket? Dielectric grease or something like that?
Just curious as to what all that is around each socket? Dielectric grease or something like that?
You do not have the required permissions to view the files attached to this post.
Regards Simon
https://www.conligwx.org - @conligwx
Davis Vantage Pro2 Plus with Daytime FARS • WeatherLink Live • Davis AirLink • PurpleAir • CumulusMX v4.0.0
https://www.conligwx.org - @conligwx
Davis Vantage Pro2 Plus with Daytime FARS • WeatherLink Live • Davis AirLink • PurpleAir • CumulusMX v4.0.0
-
- Posts: 2473
- Joined: Wed 08 Jun 2011 11:19 am
- Weather Station: Davis Vantage Pro 2 + Ecowitt
- Operating System: GNU/Linux Ubuntu 22.04 LXC
- Location: Alcaston, Shropshire, UK
- Contact:
Re: Davis anemometer transmitter problems
Hi Simon,
Whatever it is, it was there 9 years ago when I purchased the unit. I have only had the cover of the unit open about 5 times in that timespan - most of those were in the past couple of months.
-
- Posts: 2473
- Joined: Wed 08 Jun 2011 11:19 am
- Weather Station: Davis Vantage Pro 2 + Ecowitt
- Operating System: GNU/Linux Ubuntu 22.04 LXC
- Location: Alcaston, Shropshire, UK
- Contact:
Re: Davis anemometer transmitter problems
Okay, so the plug and socket have been cleaned (they were clean and corrosion-free anyway) and there has been no change. Reading John's troubleshooting guide and comparing with the symptoms, it does appear that either there is a cable fault or the reed switch is faulty. Either way I think I need to visit the Prodata shop and purchase a new anemo.
-
- Posts: 2473
- Joined: Wed 08 Jun 2011 11:19 am
- Weather Station: Davis Vantage Pro 2 + Ecowitt
- Operating System: GNU/Linux Ubuntu 22.04 LXC
- Location: Alcaston, Shropshire, UK
- Contact:
Re: Davis anemometer transmitter problems
Revisiting this: I ordered a new anemometer from Prodata during July and it was installed on the morning of the 30th. It has been working just fine since then.