Ok, Ok... been awhile and now my old clunky weather station seems to have developed a problem. Not sure if it's the transmitter or the receiver/display but I cannot get my sensor station to sync with the base unit.
The transmitter LED lights up for several seconds when I reapply power then goes into the normal 22 second (approx) blink.
The base station, upon powering up gives the normal Icon for searching for a signal for approx 10 seconds then goes into IT's normal mode, but never displays any sensor data. Correct me please, but aren't the two supposed to sync the sending/receiving cycle so that the sensor sends at the same instant the base unit receives?
Welcome to the Cumulus Support forum.
Latest Cumulus MX V3 release 3.28.6 (build 3283) - 21 March 2024
Cumulus MX V4 beta test release 4.0.0 (build 4019) - 03 April 2024
Legacy Cumulus 1 release 1.9.4 (build 1099) - 28 November 2014
(a patch is available for 1.9.4 build 1099 that extends the date range of drop-down menus to 2030)
Download the Software (Cumulus MX / Cumulus 1 and other related items) from the Wiki
Latest Cumulus MX V3 release 3.28.6 (build 3283) - 21 March 2024
Cumulus MX V4 beta test release 4.0.0 (build 4019) - 03 April 2024
Legacy Cumulus 1 release 1.9.4 (build 1099) - 28 November 2014
(a patch is available for 1.9.4 build 1099 that extends the date range of drop-down menus to 2030)
Download the Software (Cumulus MX / Cumulus 1 and other related items) from the Wiki
Rebranded WH1080 Sync problems
- Super-T
- Posts: 890
- Joined: Tue 09 Sep 2008 3:37 am
- Weather Station: wh-1081
- Operating System: Weather Laptop - Windows 10 Pro
- Location: Auckland, New Zealand
- Contact:
Re: Rebranded WH1080 Sync problems
Have you tried putting the transmitter next to the receiver in case there is an interference or low signal problem?
-
- Posts: 11
- Joined: Fri 12 Aug 2011 1:47 pm
- Weather Station: WH1080
- Operating System: Windows XP SP3
- Location: Ohio
Re: Rebranded WH1080 Sync problems
Yes they are both on my kitchen table w new batteries. I guess i am in the market to replace.
I'm getting on in years but aren't they supposed to sync tx rx?
I'm getting on in years but aren't they supposed to sync tx rx?
-
- Posts: 1124
- Joined: Sat 26 Feb 2011 1:58 pm
- Weather Station: Fine Offset 1080/1 & 3080
- Operating System: Windows XP SP3
- Location: SE London
Re: Rebranded WH1080 Sync problems
Hi,
To save battery power, the Console only activates its radio receiver for about 1 second in each 48 (when it expects the transmitter to be operating). Unfortunately it doesn't have a "Reset" mode, so you must unplug all cables and remove the batteries for perhaps half a minute or more. Then when power is applied the Console should "listen" for a transmission for up to about 5 minutes (there's an icon on the LCD to show when the receiver is active, but it's difficult to see). If it doesn't receive data within that time, then either the receiver, the transmitter or the radio link is "faulty" and is unlikely to "recover" from then on.
Cheers, Alan.
The WH1080 transmitter is a simple "Send and Hope" system, once every 48 seconds (exactly); If the LED is not flashing with that period then the transmitter (controller) is probably faulty.
To save battery power, the Console only activates its radio receiver for about 1 second in each 48 (when it expects the transmitter to be operating). Unfortunately it doesn't have a "Reset" mode, so you must unplug all cables and remove the batteries for perhaps half a minute or more. Then when power is applied the Console should "listen" for a transmission for up to about 5 minutes (there's an icon on the LCD to show when the receiver is active, but it's difficult to see). If it doesn't receive data within that time, then either the receiver, the transmitter or the radio link is "faulty" and is unlikely to "recover" from then on.
Cheers, Alan.