Hi folks,
I've got a Maplin W-1081 - had it for quite a few years.
Humidity sensor has not worked for a couple of years, not too bothered about that, but it has now stopped sensing rain!
I have the 'old' style rain-gauge unit (with holes, not grids under the bucket). Electronically it works (if I tip the buckets by hand then it registers on the base unit and in Cumulus. If I pour water in through the lid, it registers and records OK.
However, when it rains - NOTHING!
I've cleaned the whole rain unit, cleaned out the spiders and webs, ensured the sky is clear above (as in no trees!) but still no rain.
I KNOW it rained last night (I'm in Wokingham, it poured all evening and has only just stopped).
Any ideas??
I think it might be time to replace my whole station...
Welcome to the Cumulus Support forum.
Latest Cumulus MX V3 release 3.28.6 (build 3283) - 21 March 2024
Cumulus MX V4 beta test release 4.0.0 (build 4019) - 03 April 2024
Legacy Cumulus 1 release 1.9.4 (build 1099) - 28 November 2014
(a patch is available for 1.9.4 build 1099 that extends the date range of drop-down menus to 2030)
Download the Software (Cumulus MX / Cumulus 1 and other related items) from the Wiki
Latest Cumulus MX V3 release 3.28.6 (build 3283) - 21 March 2024
Cumulus MX V4 beta test release 4.0.0 (build 4019) - 03 April 2024
Legacy Cumulus 1 release 1.9.4 (build 1099) - 28 November 2014
(a patch is available for 1.9.4 build 1099 that extends the date range of drop-down menus to 2030)
Download the Software (Cumulus MX / Cumulus 1 and other related items) from the Wiki
Rain Gauge not sensing rain
-
- Posts: 1124
- Joined: Sat 26 Feb 2011 1:58 pm
- Weather Station: Fine Offset 1080/1 & 3080
- Operating System: Windows XP SP3
- Location: SE London
Re: Rain Gauge not sensing rain
Hi,
Possibly the rain is also getting into the cable/connectors. The "pull-up" current from the transmitter is very low (~25 uA) so a slight leakage (through water) can "short-out" the rain sensor switch. However, it happens that my own FO station has a very similar fault, which needed a multimeter to identify:
In my case, even with the Rain cable unplugged, the voltage being output across the "Rain" connector pins is only about 1.25 volts (which is very close to the switch sensing voltage) instead of the expected 3 volts (from the two AA cells). So sometimes it registers rain tips and sometimes it doesn't. Therefore, I plan to "open up" the transmitter box and add a pull-up resistor (from the switch pin to the + battery line). 100 kohms would give a current similar to the design value, but 10k might give more reliable operation, with negligible drain on the battery, since current only flows whilst the seesaw is actually tipping.
Cheers, Alan.
Possibly the rain is also getting into the cable/connectors. The "pull-up" current from the transmitter is very low (~25 uA) so a slight leakage (through water) can "short-out" the rain sensor switch. However, it happens that my own FO station has a very similar fault, which needed a multimeter to identify:
In my case, even with the Rain cable unplugged, the voltage being output across the "Rain" connector pins is only about 1.25 volts (which is very close to the switch sensing voltage) instead of the expected 3 volts (from the two AA cells). So sometimes it registers rain tips and sometimes it doesn't. Therefore, I plan to "open up" the transmitter box and add a pull-up resistor (from the switch pin to the + battery line). 100 kohms would give a current similar to the design value, but 10k might give more reliable operation, with negligible drain on the battery, since current only flows whilst the seesaw is actually tipping.
Cheers, Alan.
Re: Rain Gauge not sensing rain
Thanks,
But it works if I pour water through it, and tipping the bucket by hand works.
If I pour water through it will it is raining - it works.....
Baffled!!
But it works if I pour water through it, and tipping the bucket by hand works.
If I pour water through it will it is raining - it works.....
Baffled!!
-
- Posts: 272
- Joined: Tue 28 May 2013 1:06 am
- Weather Station: Davis VP2 Plus
- Operating System: Raspian Buster (RPi 3b)
- Location: Tulsa, OK
Re: Rain Gauge not sensing rain
But if you pour water through it, you're only getting the cone and the tippers wet (and whatever gets wet during the tipper emptying). If it's raining, then the whole unit gets wet.
Re: Rain Gauge not sensing rain
I tried poring water through when it was raining (hard! anorak with hood needed) and it senses the poured water, but not rain!
- beteljuice
- Posts: 3292
- Joined: Tue 09 Dec 2008 1:37 pm
- Weather Station: None !
- Operating System: W10 - Threadripper 16core, etc
- Location: Dudley, West Midlands, UK
Re: Rain Gauge not sensing rain
So ... does it register if you dribble water into the funnel ?
......................Imagine, what you will KNOW tomorrow !